Networking

Best 19-Inch Server Rack Accessories: Shelves, Cage Nuts, Panels

This post contains affiliate links. If you buy through them, we may earn a small commission at no extra cost to you. Learn more.

Do you need anything for a 19-inch rack beyond the frame and the servers? You do, and you usually find out on the day the rack arrives. The switch has no shelf to sit on, the screws in the box do not fit the holes, and the empty gaps let hot air loop back to the front. The right server rack accessories are cheap next to the gear they hold, but buying the wrong thread or a shelf that only fits a 4-post frame costs you a weekend.

Original content from computingforgeeks.com - post 181025

We picked seven accessories for a homelab or small office rack: a cantilever shelf, a heavy 4-post shelf, M6 cage nuts and screws, a brush panel, blanking panels, a horizontal cable manager and a rack fan. We checked each one against the manufacturer datasheet and the live Amazon listing again on 11 November 2026. The stock notes below are from that day. This guide pairs with our 12U homelab rack build, which uses several of these parts in a real layout.

Quick picks

If you only want the shopping list, these are the winners. Every link goes to the exact model we checked, and the price bands are what the listings showed when we wrote this:

Read the hole-type section before you add the cage nuts to your cart. Racks come with square, round or threaded holes, and the wrong fastener is the one accessory mistake you cannot fix with a screwdriver. Prices on rack hardware move every week, so check the live price on the day you order.

How we picked these accessories

What decides these parts is fit, load rating and the hardware in the box, so that is what we checked. Every pick has a manufacturer datasheet or product page behind its specs, and every Amazon link was confirmed in stock through the Amazon catalog API, with the scarce listings flagged in their sections.

A sliding shelf was on the list until we found that every real pull-out model was either out of stock or priced like a server. Several “brush panels” also turned out to be cabinet roof plates, and the section on what did not make the list covers both. We favoured StarTech and AC Infinity because both publish full spec sheets with load ratings and hardware lists, which most of the unbranded listings do not.

Server rack accessories compared

The table puts the decision specs side by side. Read the “Fits” column first, because a 2-post rack rules out the heavy shelf and a round-hole rack rules out the tool-less blanks:

PickTypeRack spaceFitsKey specPrice band
StarTech CABSHELFV1UCantilever shelf1U2-post or 4-post, front rails10 in deep, 44 lbabout $35
StarTech ADJSHELF4-post shelf1U4-post, 19.5 to 38.3 in deep175 lb, M5 hardwareabout $90
AC Infinity M6 setCage nuts and screwsNoneSquare-hole rails50 sets, 3/4 in screwsabout $19
StarTech CMBRUSH1UBrush panel1UThreaded rails as shippedNylon brush, 0.8 in deepabout $60
StarTech BLANKP10Blanking panels1U eachSquare-hole rails only10 tool-less ABS panelsabout $61
StarTech CABLMANAGER2Horizontal cable manager1UAny 19-inch rack5 D-rings, 3.5 in deepabout $36
AC Infinity CLOUDPLATE T1Rack fan panel1UAny 19-inch rack20 to 60 CFM, thermostatabout $139

Add it up and the full set comes to roughly $440, with the fan close to a third of that. Most racks do not need all seven on day one. The shelf, the cage nuts and a few blanks are the first order, and the rest can wait until the cabling or the heat tells you otherwise.

1. StarTech CABSHELFV1U: best cantilever shelf

Most homelab gear has no rack ears. A router box, a mini PC, a cable modem or a small switch all need something flat to sit on, and the CABSHELFV1U is the shelf we would buy first. It is a vented 1U tray in SPCC steel, 10 in deep, that bolts to the front rails only. That cantilever design is why it works in a 2-post relay rack as well as a 4-post cabinet, and why it is the shelf our 12U build uses twice.

StarTech CABSHELFV1U 1U vented cantilever shelf for a 19-inch server rack
StarTech CABSHELFV1U: 1U vented cantilever shelf, 10 in deep, rated for 44 lb. Image: StarTech.

StarTech rates it for 44 lb (20 kg) of stationary load and ships four M6 cage nuts, four M6 screws and four cup washers in the box, with a lifetime warranty. The vent slots matter more than they look, since a mini PC sitting on solid steel in a closed cabinet has nowhere to dump heat from its base.

If you plan to put two or three small PCs on one tray, our guide to rack mounts for mini PCs compares this shelf with the dedicated mounts.

Skip it if the load is heavy or deep. A cantilever tray hangs off two front screws, so a 1U UPS or a used 2U server will tip it forward long before it reaches 44 lb, and anything deeper than 10 in overhangs the back edge. It also ships with M6 hardware only, so a threaded 10-32 rack needs its own screws. About $35, check the CABSHELFV1U price on Amazon.

2. StarTech ADJSHELF: best 4-post shelf for heavy gear

When the thing on the shelf is a tower server, a deep UPS or a NAS full of drives, you want a shelf that bolts to all four posts. The ADJSHELF does that with brackets that slide to fit any mounting depth from 19.5 in to 38.3 in, and its tray is 27.6 in deep. StarTech rates it for 175 lb (80 kg) stationary, four times the cantilever tray, and it still takes only 1U.

StarTech ADJSHELF 1U adjustable depth 4-post server rack shelf
StarTech ADJSHELF: 1U 4-post shelf, adjusts from 19.5 to 38.3 in, rated for 175 lb. Image: StarTech.

One detail in the box catches people out. The ADJSHELF ships with M5 cage nuts, M5 screws and M5 lock nuts, not the M6 hardware most square-hole racks use. M5 cage nuts still clip into square holes, so the shelf mounts fine, but keep that bag apart from your M6 set so you never try to drive an M5 screw into an M6 nut. If the shelf is for a rackmount server rather than a tower, our first rackmount server guide covers the rails those servers ship with instead.

Skip it if you have a 2-post rack or a shallow wall-mount cabinet, since it needs rear posts at least 19.5 in behind the front ones. At about $90 it costs more than two cantilever trays, which is money wasted if all you shelve is a router. Check the ADJSHELF price on Amazon, because the listing has sat well below its list price.

3. AC Infinity M6 cage nuts and screws: best rack fasteners

Every piece of gear you rack needs four screws, and the bag that came with the rack never stretches far enough. The AC Infinity set gives you 50 matched sets of M6 screw, nylon washer and cage nut, which is enough for about a dozen devices. The screws are 3/4 in Phillips truss heads in zinc-plated carbon steel, with a pilot tip that helps them find the thread in a nut you cannot quite see.

AC Infinity M6 rack screws with cage nuts and washers, 50-piece set
AC Infinity M6 set: 50 screws, washers and cage nuts, 3/4 in long. Image: AC Infinity.

Cage nuts only belong in square-hole rails. If your rack has threaded holes, you skip the nuts entirely and buy screws that match the rail thread. AC Infinity sells the same 50-piece screw and washer set in the two common US threads, without cage nuts:

Add a cage nut tool if you are fitting more than a handful. The RackSolutions cage nut tool (about $25) hooks the far clip and levers the nut in, which saves both the rail paint and your thumbs. Its listing says it works with AC Infinity nuts but not with Ubiquiti nuts, so do not pair it with a Ubiquiti rack kit.

Skip it if your rack is threaded, because then the cage nuts are dead weight and the screw-only sets above are cheaper. If the M6 set sells out, the NavePoint set is the fallback. About $19, check the M6 set price on Amazon.

4. StarTech CMBRUSH1U: best brush panel

A brush panel is a 1U plate with a slot full of nylon bristles. Cables pass through the slot from front to back while the bristles close around them, so you get a tidy entry point without a bare steel edge sawing at your patch leads. It also keeps the front of an enclosed cabinet looking finished, and it blocks some of the dust and air that an open 1U gap would let through.

StarTech CMBRUSH1U 1U brush cable management panel for a 19-inch rack
StarTech CMBRUSH1U: 1U steel panel with a high-density nylon brush strip. Image: StarTech.

The CMBRUSH1U is a steel 1U panel with a high-density nylon brush, only 0.8 in deep, so it never fights a device mounted right behind it. StarTech ships four 10-32 and four 12-24 panel screws and no cage nuts, which tells you it was designed for threaded rails first. In a square-hole rack you use two of your M6 cage nuts and screws from section 3 instead.

Skip it if the price stings. At about $60 for one panel it costs twice the price of a Cable Matters 2-pack at about $30, and that pack ships with eight screws and cage nuts. We could only confirm the Cable Matters specs from its Amazon listing, though, and its thread is not stated, which is why the StarTech gets the pick. The StarTech also showed scarce stock, so check the CMBRUSH1U price on Amazon.

5. StarTech BLANKP10: best blanking panels

Every empty U in the front of a rack is a hole for hot exhaust air to loop back to the intake side. Blanking panels close those holes. The StarTech page says they cover unused rack units to improve airflow and keep thermal conditions stable, and Eaton describes its version the same way, as a block against hot air recirculation. In an enclosed cabinet with a fan, they decide whether the fan pulls air through your gear or around it.

StarTech BLANKP10 1U tool-less snap-in rack blanking panel
StarTech BLANKP10: ten 1U tool-less ABS blanking panels for square-hole racks. Image: StarTech.

The BLANKP10 is a 10-pack of 1U ABS panels that snap into square holes with no screws at all, which works out to about $6 a panel. Snap-in matters more than it sounds. You pull a blank every time you add a device, and ten screw-on blanks mean forty cage nuts to fit and unfit over the life of the rack. The Tripp Lite SR1UPANEL10 is the same idea at about $64 if the StarTech pack is out.

Skip it if your rack has round or threaded holes, because the snap-in tabs only hold in square ones. For those racks the Cable Matters steel 2-pack (about $22, with M6 screws and nuts per its listing) screws on instead. Ten panels is also more than a half-empty 12U rack needs. About $61, check the BLANKP10 price on Amazon.

6. StarTech CABLMANAGER2: best horizontal cable manager

A horizontal cable manager sits next to the patch panel and the switch and holds the slack in your patch cords, so they run sideways in neat lines instead of hanging in loops over the ports. The CABLMANAGER2 is the plain steel 1U version with five removable ABS D-rings spaced 4 in apart. The two end rings rotate 90 degrees, which helps when cords turn the corner to a vertical run at the side of the rack.

StarTech CABLMANAGER2 1U horizontal rack cable manager with D-ring hooks
StarTech CABLMANAGER2: 1U steel panel with five removable D-rings, 3.5 in deep. Image: StarTech.

It sticks out 3.5 in from the rails, so check that a front door still closes on an enclosed cabinet. StarTech gives it a 2-year warranty, and the box contents list no mounting screws, so plan on two sets from your cage nut bag. In our 12U layout it sits at U10, directly under the patch panel at U11 and the switch at U12, so the slack from both drops straight into the rings.

Skip it if you run more cords through one manager than a 24-port switch needs. Five D-rings hold a couple of dozen thin patch leads before they start to bulge. A StarTech cable lacing bar (about $24, scarce stock, specs from its Amazon listing) is the cheaper option at the back of the rack, where you tie cables down rather than route them. About $36, check the CABLMANAGER2 price on Amazon.

7. AC Infinity CLOUDPLATE T1: best rack fan

An open-frame rack in a cool room does not need a fan. An enclosed cabinet in a closet does, because the heat from a switch, a NAS and a couple of servers has nowhere to go. The CLOUDPLATE T1 is a 1U panel with six dual-ball-bearing fans that move 20 to 60 CFM at 8 to 28 dBA, controlled by an LCD thermostat on a 6 ft probe. You set a target temperature and the fans ramp only when the cabinet gets warm.

AC Infinity CLOUDPLATE T1 1U rack exhaust fan panel with thermostat
AC Infinity CLOUDPLATE T1: 1U exhaust fan panel, six fans, 20 to 60 CFM, thermostat control. Image: AC Infinity.

The T1 is the exhaust model, so it belongs near the top of the rack where the hot air collects. It runs on 12 V DC at 8 W from a wall adapter that accepts 100 to 240 V, and it ships with its own screws and cage nuts. AC Infinity quotes an L10 life of 67,000 hours for the fans.

Pair it with the blanking panels from section 5, or the fan will simply pull cool room air in through the empty gaps and leave the hot spots alone.

Skip it if your rack is open frame, or if you need intake rather than exhaust. The CLOUDPLATE T1-N is the intake version and the CLOUDPLATE T7 is a 2U exhaust model, both around the same price. At about $139 it is the priciest pick here, and 28 dBA at full speed is quiet but still audible in a silent room. Check the CLOUDPLATE T1 price on Amazon.

Match the hole type before you order

A 19-inch rack is a standard for width and height, not for holes. One rack unit is 1.75 in (44.45 mm), and the mounting holes repeat in the same three-hole pattern on every rack, as the 19-inch rack standard sets out. What each hole accepts is up to the rack maker, and that is what decides your fasteners, your blanks and half the accessories above:

Rail holeWhat goes in itAccessories that fit
SquareCage nuts, then M6 (sometimes M5) screwsEverything here, including the snap-in blanks
Threaded (tapped)Screws straight into the post, often 10-32 or 12-24All but the tool-less blanks, with screws in your thread for the shelves; no cage nuts
Round (clearance)Screws with a nut or cage nut behindScrew-on parts only; no snap-in blanks

Our 12U rack build notes that M5 is close to 10-32 in size and M6 is close to 12-24, which is exactly why people cross-thread them. Check the rack manual or the bag in its box for the thread before you order, then buy one bag of that thread and use it for everything. If you have not bought the rack yet, our homelab server rack guide notes which frames use square holes for cage nuts and which use round holes for clip nuts.

Depth is the other number that bites. Measure the distance between your front and rear posts before buying the 4-post shelf, and measure the space in front of the rails before adding a cable manager or a brush panel to a cabinet with a door. The same goes for power: a rack PDU takes 1U too, and our rack PDU guide compares the metered, switched and smart strips worth that slot.

What did not make the list

Some accessories looked like obvious picks until we checked the listings. Each one below failed on stock, fit or price when we checked them:

  • Sliding shelves: StarTech UNISLDSHF19 not buyable, Tripp Lite 1U out of stock
  • Tripp Lite SRSHELF4PSLHD: in stock, but over $460
  • APC blanking panels: priced far above the StarTech and Tripp Lite packs
  • NavePoint brush strip panel: a cabinet roof plate, not a 1U panel
  • Tripp Lite SR1UBRUSH: one unit left, third-party seller

The sliding shelf is the one we wanted most. Many Amazon results called “sliding” are depth-adjustable 4-post shelves that do not pull out at all, so read the listing for an extension figure before you trust the name. Until a real pull-out shelf is back in stock at a sane price, the ADJSHELF is the better buy for anything heavy, and a cantilever tray is fine for a keyboard or a small console.

If your rack is a 10-inch mini rack instead, none of these parts fit it, and our 10-inch rack accessories guide covers the narrower parts.

Which accessories to buy first

You do not need all seven on the day the rack arrives. Buy in the order the rack fills up, and let the gear tell you when the next accessory earns its slot:

  1. A bag of fasteners in the rail thread
  2. A cantilever shelf for the gear without ears
  3. Blanking panels for every empty U
  4. A cable manager once you add a patch panel
  5. A brush panel when cables cross to the back
  6. A 4-post shelf for a tower or a heavy UPS
  7. A rack fan if the cabinet is enclosed and warm

The first three cost about $80 together with the M6 set, one shelf and a pair of steel blanks, and they solve the problems you hit in the first hour. The fan comes last on purpose. Fill the gaps with blanks before you spend $139 on airflow, because a fan in a rack full of holes mostly cools the room. If you are planning the rest of the build, start with our rackmount case picks for the servers themselves.

Keep reading

Free CCNA 200-301 Practice Questions with Answers Networking Free CCNA 200-301 Practice Questions with Answers Configure Samba File Share on Debian 13 / 12 Debian Configure Samba File Share on Debian 13 / 12 WireGuard VPN Setup: Ubuntu 26.04/24.04, Debian 13, Rocky 10 Debian WireGuard VPN Setup: Ubuntu 26.04/24.04, Debian 13, Rocky 10 Best Networking Books: TCP/IP, Routing and Troubleshooting Books Best Networking Books: TCP/IP, Routing and Troubleshooting Omada Fusion Pro Behind a Router: Port Forwarding for LAN Access Networking Omada Fusion Pro Behind a Router: Port Forwarding for LAN Access Install Tor Browser on Ubuntu 26.04, Debian 13 and Linux Mint 22 Debian Install Tor Browser on Ubuntu 26.04, Debian 13 and Linux Mint 22

Leave a Comment

Press ESC to close