Repository navigation
5.11 Alpha (Painting + Bambu) #20899
Replies: 4 comments 13 replies
This comment was marked as off-topic.
This comment was marked as off-topic.
|
Some initial observations with the 5.11 Alpha. 2025-08-28 20:07:43,059 - DEBUG - [MainThread] UM.Controller.setActiveStage [222]: Setting active stage to PreviewStage
2025-08-28 20:07:43,080 - DEBUG - [MainThread] UM.Controller.setActiveView [110]: Setting active view to SimulationView
2025-08-28 20:07:43,084 - DEBUG - [MainThread] UM.Mesh.MeshData.calculateNormalsFromVertices [673]: Calculating normals took 0.0 seconds
2025-08-28 20:07:43,181 - DEBUG - [MainThread] STLReader.STLReader._read [68]: Loaded a mesh with 12612 vertices
2025-08-28 20:07:43,183 - DEBUG - [MainThread] UM.View.GL.ShaderProgram.load [62]: Loading [C:\Program Files\UltiMaker Cura 5.11.0-alpha.0\share\cura\plugins\SimulationView\simulationview_composite.shader]...
2025-08-28 20:07:43,230 - WARNING - [MainThread] UM.Qt.Bindings.Theme.getColor [120]: No color layerview_move_while_retracting defined in Theme
2025-08-28 20:07:43,231 - WARNING - [MainThread] UM.Qt.Bindings.Theme.getColor [120]: No color layerview_move_while_unretracting defined in Theme
2025-08-28 20:07:43,296 - DEBUG - [MainThread] UM.Controller._updateActiveView [150]: Setting active view to SolidView
2025-08-28 20:07:43,296 - DEBUG - [JobQueueWorker [1]] CuraEngineBackend.ProcessSlicedLayersJob.run [74]: Processing new layer for build plate 0...
2025-08-28 20:07:43,298 - DEBUG - [MainThread] UM.Controller.setActiveStage [222]: Setting active stage to PrepareStage
2025-08-28 20:07:43,440 - WARNING - [JobQueueWorker [1]] UM.Qt.Bindings.Theme.getColor [120]: No color layerview_move_while_retracting defined in Theme
2025-08-28 20:07:43,441 - WARNING - [JobQueueWorker [1]] UM.Qt.Bindings.Theme.getColor [120]: No color layerview_move_while_unretracting defined in Theme
2025-08-28 20:07:43,469 - DEBUG - [MainThread] UM.View.GL.ShaderProgram.load [62]: Loading [C:\Program Files\UltiMaker Cura 5.11.0-alpha.0\share\cura\resources\shaders\xray.shader]...
2025-08-28 20:07:49,265 - DEBUG - [JobQueueWorker [1]] CuraEngineBackend.ProcessSlicedLayersJob.run [254]: Processing layers took 5.965237855911255 seconds
2025-08-28 20:07:49,266 - DEBUG - [MainThread] CuraEngineBackend.CuraEngineBackend._onProcessLayersFinished [1143]: See if there is more to slice(2)... |
|
I've had a little time to try out the seam painter today. I tried it with a couple of models with vertical surfaces where I tried to place the seam in a different location to where the walls seam settings would normally have put it, however I was finding that the walls seam settings were still being used & the painted seams were being ignored so I wondered if they is maybe some insight from yourselves that would explain why it's happening and how the seam painter & walls settings are supposed to interact with each other |




Uh oh!
There was an error while loading. Please reload this page.
Uh oh!
There was an error while loading. Please reload this page.
🖼️Painting + Bambu Build🖼️ (5.11 Alpha)
A nightly build with Painting 🎨 and Bambu 🎋
Once again, two sizeable new features that we'd like to have your feedback on have (nearly) arrived to Cura!
Also, we've introduced a feature just for builds like this; where you can select if you'd like to 'start clean' or use the current configuration folder -- this helps not contaminate your main config should the alpha still have some issues. -- Also the banner-colour on the top is different from our usual deep blue, to let you know this isn't a normal release (or beta).
Painting 🎨
Painting, or various tasks that practically require paint-on functionality, have been a much requested feature for a good while. For now with the first introduction of paint-on in Cura, two of those features are coming along:
We are exploring other painting applications, like Paint On Support, but those are more effort than expected and might not show up in the upcoming release.
Known issues 🦟
Bambu 🎋
Part of the reason Bambu-printers are so fast is that they have to do very little on-board operations w.r.t. gcode-postprocessing -- nearly everything is done by the slicer. Now, that slicer can be Cura.
Of course, with their multi-material capabilities, this synergizes with material-painting. (Just as with our own dual-extrusion.)
Known issues 🦟
Other Changes 🎁
All of this is built on top of our (current) in-progress work for the upcoming release, so you might see some other features pop-up, such as:
As well as a whole host of bug fixes, new printers and other improvements.
Why do we need you? 😎
What do you need to do? 💪
Well, not much, just download this version, use it as you would usually do, and send a brief feedback on the discussion: describe your environment, and tell us if everything went fine, or if you encountered some crashes or strange behaviours!
This discussion was created from the release 5.11 Alpha (Painting + Bambu).
Update
Known issues:
All reactions