Skip to content

Releases

Meshtastic Firmware 2.8.2.d5f1619 Alpha

Pre-release

Choose a tag to compare

@github-actions github-actions released this 04 Nov 00:09
d5f1619

Important

XEdDSA signing policy has changed. In Compatible mode, nodes no longer sign packets; AES-CCM now takes precedence, and Strict mode gains exemptions. Review your signing settings after updating. (#12191)
Key verification is now refused when licensed (ham) mode is enabled. (#12201)

Note

MQTT gateways now uplink PKI direct messages they relay but cannot decrypt. These messages stay end-to-end encrypted. (#12110)

Re-release of 2.8.2 to fix a stack exhaustion bug in environmental telemetry.

🌟 Highlights

📡 Radio performance and reliability

  • Smarter Listen Before Talk: CAD-to-RX handoff, correct symbol timing, and better thresholds (#11137)
  • Received LoRa frames are now read from a dedicated FreeRTOS task (#11983)
  • Fixes for many RX/TX edge cases:
    • Preamble hold sized for the worst-case frame (#12125)
    • Damaged-header CAD handoffs now end cleanly (#12144)
    • A stale RX flag can no longer clobber a live frame (#12153)
    • SX126x re-stages a TX after the modem parameters change (#12101)
  • AGC is reset only when the radio has gone quiet (or once a day), and the RadioLib BUSY wait is bounded (#12072, #12105)

🔐 Security and PKI

  • Faster encrypted packets with a shared-secret cache (#11979)
  • nRF52840 now runs X25519 and Ed25519 verification on the CC310 hardware crypto engine (#12098)
  • Relays no longer rewrite NodeInfo or NeighborInfo payloads (#12088, #12090)
  • Imported private keys are clamped before the public key is derived (#12095)
  • Further hardening against incoming packets with spoofed own node num (#12270)

🐧 meshtasticd (Linux / Raspberry Pi)

  • BLE peripheral support via BlueZ: connect the phone apps directly to a Pi node (#11396)
  • DMShell: remote shell over the mesh, with an on-board test client (#11976, #12111)
  • Native mDNS discovery via Avahi and Bonjour (#12032, #12142)
  • Host notifications (#10216)
  • Admin keys in config.yaml, no longer limited to three (#12056)
  • Faster CH341 USB radio handling (#12013, #12016)
  • Adafruit Arcade Bonnet input (#12116)

🖥️ Displays

  • InkHUD: offline maps from an SD card (#12118), plus an InkHUD port for the ThinkNode M5 (#12097)
  • Ethernet status is now shown on the WiFi screen (#11991)

🔧 New and improved hardware

  • New boards:
  • RAK2560 WisMesh Hub SensorHub uplink (#11817)
  • T-Beam 1W now supports the LR1121 and LR2021 modules (#12204)
  • GPS updates for ThinkNode M5 and M8, Wio Tracker L2 fixes, and the Meshnology W12 front end (#12113, #12151, #12133, #12238)

🩹 Notable fixes

  • Fixed an ESP32 light-sleep crash caused by a DIO1 interrupt storm (#12131)
  • Fixed a crash when enabling Store & Forward after a boot with it disabled (#12168)
  • Deferred NodeDB saves are no longer dropped (#11930)
  • ESP32 shutdown and BLE OTA DFU reliability fixes (#12159, #12220)

Meshtastic Firmware 2.8.2.4c89b69 Alpha (Revoked)

Choose a tag to compare

@github-actions github-actions released this 02 Nov 18:26
4c89b69

Important

XEdDSA signing policy has changed. In Compatible mode, nodes no longer sign packets; AES-CCM now takes precedence, and Strict mode gains exemptions. Review your signing settings after updating. (#12191)
Key verification is now refused when licensed (ham) mode is enabled. (#12201)

Note

MQTT gateways now uplink PKI direct messages they relay but cannot decrypt. These messages stay end-to-end encrypted. (#12110)

🌟 Highlights

📡 Radio performance and reliability

  • Smarter Listen Before Talk: CAD-to-RX handoff, correct symbol timing, and better thresholds (#11137)
  • Received LoRa frames are now read from a dedicated FreeRTOS task (#11983)
  • Fixes for many RX/TX edge cases:
    • Preamble hold sized for the worst-case frame (#12125)
    • Damaged-header CAD handoffs now end cleanly (#12144)
    • A stale RX flag can no longer clobber a live frame (#12153)
    • SX126x re-stages a TX after the modem parameters change (#12101)
  • AGC is reset only when the radio has gone quiet (or once a day), and the RadioLib BUSY wait is bounded (#12072, #12105)

🔐 Security and PKI

  • Faster encrypted packets with a shared-secret cache (#11979)
  • nRF52840 now runs X25519 and Ed25519 verification on the CC310 hardware crypto engine (#12098)
  • Relays no longer rewrite NodeInfo or NeighborInfo payloads (#12088, #12090)
  • Imported private keys are clamped before the public key is derived (#12095)
  • Further hardening against incoming packets with spoofed own node num (#12270)

🐧 meshtasticd (Linux / Raspberry Pi)

  • BLE peripheral support via BlueZ: connect the phone apps directly to a Pi node (#11396)
  • DMShell: remote shell over the mesh, with an on-board test client (#11976, #12111)
  • Native mDNS discovery via Avahi and Bonjour (#12032, #12142)
  • Host notifications (#10216)
  • Admin keys in config.yaml, no longer limited to three (#12056)
  • Faster CH341 USB radio handling (#12013, #12016)
  • Adafruit Arcade Bonnet input (#12116)

🖥️ Displays

  • InkHUD: offline maps from an SD card (#12118), plus an InkHUD port for the ThinkNode M5 (#12097)
  • Ethernet status is now shown on the WiFi screen (#11991)

🔧 New and improved hardware

  • New boards:
  • RAK2560 WisMesh Hub SensorHub uplink (#11817)
  • T-Beam 1W now supports the LR1121 and LR2021 modules (#12204)
  • GPS updates for ThinkNode M5 and M8, Wio Tracker L2 fixes, and the Meshnology W12 front end (#12113, #12151, #12133, #12238)

🩹 Notable fixes

  • Fixed an ESP32 light-sleep crash caused by a DIO1 interrupt storm (#12131)
  • Fixed a crash when enabling Store & Forward after a boot with it disabled (#12168)
  • Deferred NodeDB saves are no longer dropped (#11930)
  • ESP32 shutdown and BLE OTA DFU reliability fixes (#12159, #12220)

Meshtastic Firmware 2.8.1.8e6a88d Alpha

Pre-release

Choose a tag to compare

@github-actions github-actions released this 01 Oct 17:19
8e6a88d

🚀 Big changes

Warning

New US nodes now default to LongTurbo, not LongFast. Only applies to first-time region selection on the device screen. LongTurbo and LongFast can't hear each other. You will need to switch the preset back to LongFast to join an existing mesh on the prior default. (#11637)

A problem was found in the 2.8.0 packet signing code. 2.8.0 has been revoked, and 2.8.1 signatures are not compatible with the revoked 2.8.0 firmware.

Important

If you hit a bootloop or repeated crashes after upgrading, we recommend a full erase and flash. Export your config first to backup first, if you have any important settings you want to save.

There are a number of fundamental changes to 2.8 that require a heads-up. Please review some of these higher profile changes so that you are aware of them before installing:

  • Node numbers (ID) are now derived from the public-key identity of the node instead of hardware mac address
  • XEdDSA based packet signing
  • Reduction of long-name to 25 bytes
  • Precise position no longer allowed on known-keys (public mesh. Please use private channels for this)
  • Telemetry and position are off-by-default and must be opted into
  • Ground-up redesigned NodeDB storage and traffic management
  • Completely new allocation of LoRa Regions and presets, including ham specific carve-outs
  • Signing acks with the Ack_proof field

Other high-impact changes

Radio & mesh protocol

  • Packet Signing via XEdDSA (#10478) plus a BaseUI signing status UI (#10841), unsigned-packet policy hardening with test coverage (#10858), and runtime-toggleable MESHTASTIC_LOCKDOWN hardening for nRF52 (#10349, opt-in via #10712).
  • Sign the whole Data envelope, in one unambiguous layout by @jp-bennett in #11422
  • Send an ack over PKC when no channel can carry it by @jp-bennett in #11891
  • Traffic Management Module for packet forwarding — dedup, rate limiting, role-aware policing (#9358 base, #10706 dedup/rate-limit expansion, #10745 next-hop cache overflow store, #9921 congestion-aware position interval/hop-exhaustion tuning).
  • Automatic variable hop limits based on live mesh activity and message-size estimation (#10176).
  • Mesh beacon feature and admin controls (#10618 base implementation, #10839 second pass adding beacon admin/config).
  • Noise floor tracking with a sliding-window estimate (#9347).
  • Hash table index for O(1) packet history lookups — improves routing/dedup performance on busy meshes (#9499).
  • New amateur-radio regions: 70cm (#10627), 1.25m/125cm (#10638), 2m/~144MHz (#10623); EU regions merge plus Narrow/Lite region enablement for EU (#10675, #10120); LoRa region preset map for cleaner per-region defaults (#10736).
  • TinyFast and TinySlow modem presets added to config and menu (#10597).
  • LoRa config changes now apply live without a reboot (#9962); LoRa settings expansion and validation improvements (#9878).
  • Position privacy: direct-send position packets are clamped to channel precision (#10383), and public/known-key position precision is clamped similarly (#10665) and honors explicit channel settings to prevent location leaks (#10513).
  • Licensed operators are now prevented from rebroadcasting packets to/from unlicensed users, for regulatory compliance (#9958).
  • Packets with missing/invalid hop_start (pre-hop firmware) are now deprecated/blocked (#9476).
  • Spoof detection added for UDP multicast packets (#9905).
  • Low-bandwidth conversion support added to MeshRadio (#10595).
  • ATAK Plugin V2 implemented (drops legacy unishox2 compression) (#10105), including TAKTALK voice/text chat message and room data structures.
  • Ethernet HTTP/HTTPS API server ported to RP2350 + W5500 boards (#10573), plus Ethernet OTA support for RP2350/W5500 (#10136).
  • Optional LED_LORA indicator to show LoRa TX activity (#10465), and an LED indicator for LoRa RX (#10674).
  • GPS time sync: device now sets its clock from GPS every 30 minutes (#10737); GPS is skipped at startup if the LoRa region is unset, to save battery (#10386); GPS model/baudrate now cached across reboots to skip a full sweep (#10544).
  • Config: position & telemetry broadcast are now opt-in rather than always-on (#10929).

UI / display — BaseUI

BaseUI is the current default graphical UI (src/graphics/Screen.cpp, draw/UIRenderer, draw/MenuHandler, draw/CompassRenderer, draw/NotificationRenderer, draw/NodeListRenderer).

  • Color support for TFT-equipped nodes (#10233).
  • "Ham Mode" — prompts for new Amateur Radio regions (#10663).
  • Status-message display added to Favorite/NodeList screens (#9504, #10197).
  • Hex picker UI added for entering hex values (#10650).
  • Save/restore of frame visibility state across sessions (#10576).
  • BLE pairing PIN now shown via a proper on-screen banner (#8902).
  • Compass rendering/behavior improvements (#10166).
  • Emote handling refactor (#9896).
  • Games joystick input by @jp-bennett in #11917
  • Allow Spacebar to advance frames by @Xaositek in #11771
  • Don't show new message banner on message screen by @HarukiToreda in #11671
  • Let a module hold the screen by @caveman99 in #11631

UI / display — InkHUD

InkHUD is the e-ink-optimized UI (src/graphics/niche/InkHUD).

  • Offline map tiles with zoom controls (#10785) and general GPS UX improvements (#10846).
  • Full touch support for the T5 E-Paper S3 (#10286) and a full InkHUD port for the LilyGo T5 E-Paper S3 Pro (#10211).
  • "Wipe all messages" option (#10721).
  • T-mini E-Ink S3 support added (#9856).

UI / display — MUI

UI / display — shared / cross-cutting

Touches the display driver layer or more than one UI system at once.

  • InkHUD and BaseUI message store unified into a shared implementation (#10596).
  • T-mini E-Ink S3 support landed for both InkHUD and BaseUI (#9856).
  • Board-specific TFT driver support and simplified TFT ifdef chains for easier porting (#10827, #10803); faster TFT color conversion (#10814); touchscreen variant flags (VARIANT_TOUCHSCREEN/ENABLE_TOUCH_INT) added for new touch boards (#10815).

Backend / developer-facing features

Memory & stability infrastructure

  • MemClass.h — a central memory-class ladder providing fail-safe-small defaults across constrained platforms (#10901).
  • MemAudit — per-subsystem heap accounting reported in the boot log (#10900).
  • nRF52 heap tiers and SoftDevice RAM reservation right-sized, freeing an extra ~8KB heap arena (#10898, #10903).
  • Native Portduino malloc shim added for more realistic memory behavior in simulation (#10677).
  • Bluetooth memory freed automatically when Wi-Fi is enabled or Bluetooth is disabled (#10398); Bluetooth wait is skipped entirely when disabled (#10571).
  • NodeDB "warm store" — new persistent warm-tier node storage layer (#10705 base, #10746/#10759 right-sizing for constrained platforms, #10809 fixing associated spiLock deadlocks).
  • 2.8 NodeDB shrink/decoupling/restructuring to reduce per-node memory footprint (#10413).
  • Flash hardening, filesystem platform unification, and a write-behind LFS cache for STM32WL/nRF52 — a storage-format break (#10171).

New APIs / module-author infrastructure

  • MCP server added for interacting with Meshtastic devices and driving a testing framework / TUI, later extracted to its own repo (#10194, #10861).
  • Native "sensors" simulation support for Portduino (#10748); PortduinoSetOptions to override the realhardware flag for tests (#10157).
  • Hardfault handler added for STM32, making crashes visibly obvious in logs (#10071).
  • BinarySemaphorePosix implemented with proper pthread synchronization for native builds (#9895).
  • NimBLE parameter overhaul, including a fix attempt for incompatible BLE bond cleanup (#10741).
  • STM32 ADC support added to AnalogBatteryLevel (#9369).
  • JSON library dependency removed from firmware builds while retaining full JSON support in meshtastic...
Read more

Meshtastic Firmware 2.8.0.47db0e3 Alpha (Revoked)

Choose a tag to compare

@github-actions github-actions released this 01 Sep 10:56
47db0e3

🚀 Big changes

Warning

New US nodes now default to LongTurbo, not LongFast. Only applies to first-time region selection on the device screen. LongTurbo and LongFast can't hear each other. You will need to switch the preset back to LongFast to join an existing mesh on the prior default. (#11637)

Important

If you hit a bootloop or repeated crashes after upgrading, we recommend a full erase and flash. Export your config first to backup first, if you have any important settings you want to save.

There are a number of fundamental changes to 2.8 that require a heads-up. Please review some of these higher profile changes so that you are aware of them before installing:

  • Node numbers (ID) are now derived from the public-key identity of the node instead of hardware mac address
  • XEdDSA based packet signing
  • Reduction of long-name to 25 bytes
  • Precise position no longer allowed on known-keys (public mesh. Please use private channels for this)
  • Telemetry and position are off-by-default and must be opted into
  • Ground-up redesigned NodeDB storage and traffic management
  • Completely new allocation of LoRa Regions and presets, including ham specific carve-outs

Other high-impact changes

Radio & mesh protocol

  • Packet Signing via XEdDSA (#10478) plus a BaseUI signing status UI (#10841), unsigned-packet policy hardening with test coverage (#10858), and runtime-toggleable MESHTASTIC_LOCKDOWN hardening for nRF52 (#10349, opt-in via #10712).
  • Traffic Management Module for packet forwarding — dedup, rate limiting, role-aware policing (#9358 base, #10706 dedup/rate-limit expansion, #10745 next-hop cache overflow store, #9921 congestion-aware position interval/hop-exhaustion tuning).
  • Automatic variable hop limits based on live mesh activity and message-size estimation (#10176).
  • Mesh beacon feature and admin controls (#10618 base implementation, #10839 second pass adding beacon admin/config).
  • Noise floor tracking with a sliding-window estimate (#9347).
  • Hash table index for O(1) packet history lookups — improves routing/dedup performance on busy meshes (#9499).
  • New amateur-radio regions: 70cm (#10627), 1.25m/125cm (#10638), 2m/~144MHz (#10623); EU regions merge plus Narrow/Lite region enablement for EU (#10675, #10120); LoRa region preset map for cleaner per-region defaults (#10736).
  • TinyFast and TinySlow modem presets added to config and menu (#10597).
  • LoRa config changes now apply live without a reboot (#9962); LoRa settings expansion and validation improvements (#9878).
  • Position privacy: direct-send position packets are clamped to channel precision (#10383), and public/known-key position precision is clamped similarly (#10665) and honors explicit channel settings to prevent location leaks (#10513).
  • Licensed operators are now prevented from rebroadcasting packets to/from unlicensed users, for regulatory compliance (#9958).
  • Packets with missing/invalid hop_start (pre-hop firmware) are now deprecated/blocked (#9476).
  • Spoof detection added for UDP multicast packets (#9905).
  • Low-bandwidth conversion support added to MeshRadio (#10595).
  • ATAK Plugin V2 implemented (drops legacy unishox2 compression) (#10105), including TAKTALK voice/text chat message and room data structures.
  • Ethernet HTTP/HTTPS API server ported to RP2350 + W5500 boards (#10573), plus Ethernet OTA support for RP2350/W5500 (#10136).
  • Optional LED_LORA indicator to show LoRa TX activity (#10465), and an LED indicator for LoRa RX (#10674).
  • GPS time sync: device now sets its clock from GPS every 30 minutes (#10737); GPS is skipped at startup if the LoRa region is unset, to save battery (#10386); GPS model/baudrate now cached across reboots to skip a full sweep (#10544).
  • Config: position & telemetry broadcast are now opt-in rather than always-on (#10929).

UI / display — BaseUI

BaseUI is the current default graphical UI (src/graphics/Screen.cpp, draw/UIRenderer, draw/MenuHandler, draw/CompassRenderer, draw/NotificationRenderer, draw/NodeListRenderer).

  • Color support for TFT-equipped nodes (#10233).
  • "Ham Mode" — prompts for new Amateur Radio regions (#10663).
  • Status-message display added to Favorite/NodeList screens (#9504, #10197).
  • Hex picker UI added for entering hex values (#10650).
  • Save/restore of frame visibility state across sessions (#10576).
  • BLE pairing PIN now shown via a proper on-screen banner (#8902).
  • Compass rendering/behavior improvements (#10166).
  • Emote handling refactor (#9896).

UI / display — InkHUD

InkHUD is the e-ink-optimized UI (src/graphics/niche/InkHUD).

  • Offline map tiles with zoom controls (#10785) and general GPS UX improvements (#10846).
  • Full touch support for the T5 E-Paper S3 (#10286) and a full InkHUD port for the LilyGo T5 E-Paper S3 Pro (#10211).
  • "Wipe all messages" option (#10721).
  • T-mini E-Ink S3 support added (#9856).

UI / display — MUI

UI / display — shared / cross-cutting

Touches the display driver layer or more than one UI system at once.

  • InkHUD and BaseUI message store unified into a shared implementation (#10596).
  • T-mini E-Ink S3 support landed for both InkHUD and BaseUI (#9856).
  • Board-specific TFT driver support and simplified TFT ifdef chains for easier porting (#10827, #10803); faster TFT color conversion (#10814); touchscreen variant flags (VARIANT_TOUCHSCREEN/ENABLE_TOUCH_INT) added for new touch boards (#10815).

Backend / developer-facing features

Memory & stability infrastructure

  • MemClass.h — a central memory-class ladder providing fail-safe-small defaults across constrained platforms (#10901).
  • MemAudit — per-subsystem heap accounting reported in the boot log (#10900).
  • nRF52 heap tiers and SoftDevice RAM reservation right-sized, freeing an extra ~8KB heap arena (#10898, #10903).
  • Native Portduino malloc shim added for more realistic memory behavior in simulation (#10677).
  • Bluetooth memory freed automatically when Wi-Fi is enabled or Bluetooth is disabled (#10398); Bluetooth wait is skipped entirely when disabled (#10571).
  • NodeDB "warm store" — new persistent warm-tier node storage layer (#10705 base, #10746/#10759 right-sizing for constrained platforms, #10809 fixing associated spiLock deadlocks).
  • 2.8 NodeDB shrink/decoupling/restructuring to reduce per-node memory footprint (#10413).
  • Flash hardening, filesystem platform unification, and a write-behind LFS cache for STM32WL/nRF52 — a storage-format break (#10171).

New APIs / module-author infrastructure

  • MCP server added for interacting with Meshtastic devices and driving a testing framework / TUI, later extracted to its own repo (#10194, #10861).
  • Native "sensors" simulation support for Portduino (#10748); PortduinoSetOptions to override the realhardware flag for tests (#10157).
  • Hardfault handler added for STM32, making crashes visibly obvious in logs (#10071).
  • BinarySemaphorePosix implemented with proper pthread synchronization for native builds (#9895).
  • NimBLE parameter overhaul, including a fix attempt for incompatible BLE bond cleanup (#10741).
  • STM32 ADC support added to AnalogBatteryLevel (#9369).
  • JSON library dependency removed from firmware builds while retaining full JSON support in meshtasticd (#10152) — reduces firmware footprint for module authors relying on the JSON path.
  • Improved manual build flow / developer build ergonomics (#8839).- External Notifications module logic fully reworked for more flexible notification rules (#10006).

Full Changelog: v2.7.23.b246bcd...v2.8.0.47db0e3

Meshtastic Firmware 2.8.0.7239fe8 (Revoked)

Choose a tag to compare

@github-actions github-actions released this 30 Aug 00:52
7239fe8

Warning

This initial cut of 2.8.0 was revoked due to issues encountered with LR1110 initialization. This became apparent on T1000-E devices after a fresh flash. Please download https://github.com/meshtastic/firmware/releases/tag/v2.8.0.47db0e3 instead.

Meshtastic Firmware 2.7.26.54e0d8d Beta

Choose a tag to compare

@github-actions github-actions released this 24 Jun 11:19
54e0d8d

Warning

If you encounter touch screen accuracy issues on a T-Deck, please run the screen calibration in MUI tools.

🐛 Bug fixes and maintenance

⚙️ Dependencies

  • Update Sensirion I2C SCD30 to v1.1.1 by @app/renovate in #10294
  • Update alpine Docker tag to v3.24 by @app/renovate in #10668
  • Update actions/github-script action to v9 by @app/renovate in #10691
  • Update meshtastic/device-ui digest to 4ec010c by @app/renovate in #10732
  • Update meshtastic/device-ui digest to 6cadf54 by @app/renovate in #10743
  • Update actions/checkout action to v7 by @app/renovate in #10744
  • Update meshtastic/device-ui digest to 1c45ebc by @app/renovate in #10749
  • Update platform-native digest to 61067ac by @app/renovate in #10750

Full Changelog: v2.7.25.104df5f...v2.7.26.54e0d8d

Meshtastic Firmware 2.7.25.104df5f Alpha

Choose a tag to compare

@github-actions github-actions released this 10 Jun 00:18
104df5f

🚀 Enhancements

🐛 Bug fixes and maintenance

  • Add Heltec mesh node t1 by @Quency-D in #10416
  • Fix SHT2x detection for INA219 addresses by @balya in #10482
  • Missing module config in rak6421 / 13300 + 13302 module config files. by @Littleaton in #10496
  • Add Lilygo T-Impulse-Plus by @vidplace7 in #10497
  • Preserve forwarded position payload precision by @h3lix1 in #10554
  • Fix mini-epaper-s3 build: resolve SensorLib isBitSet macro conflict with SparkFun MMC5983MA by @app/copilot-swe-agent in #10584
  • Debian: Correctly build without signing (for forks) by @vidplace7 in #10605
  • Add Module configuration for RAK6421 Slot 2 yamls by @pdxlocations in #10632

⚙️ Dependencies

  • Update platformio/ststm32 to v19.6.0 by @app/renovate in #10329
  • Update libpax digest to 1730234 by @app/renovate in #10507
  • Update ESP32-CH390 to v1.1.0 by @vidplace7 in #10528
  • Update actions/stale action to v10.3.0 by @app/renovate in #10532
  • Update meshtastic/device-ui digest to 34e96d2 by @app/renovate in #10537
  • Update meshtastic-esp8266-oled-ssd1306 digest to 2e26010 by @app/renovate in #10562
  • Update Adafruit SSD1306 to v2.5.17 by @app/renovate in #10581
  • Update SparkFun MMC5983MA Magnetometer to v1.1.5 by @app/renovate in #10599
  • Update meshtastic/device-ui digest to 502ba30 by @app/renovate in #10629

Full Changelog: v2.7.24.472b14c...v2.7.25.104df5f

Meshtastic Firmware 2.7.24.472b14c Alpha

Choose a tag to compare

@github-actions github-actions released this 23 May 01:12

🚀 Enhancements

  • ThinkNode M7 by @caveman99 in #8077
  • Implement rotating JSONL recorder for persistent logging by @thebentern in #10428
  • Make power status logging less chatty and track battery presence transitions by @thebentern in #10453
  • Add variantDefaultConfig and set eth_enabled to default true by @jp-bennett in #10454
  • VSCode: Prepare for pioarduino transition by @vidplace7 in #10471
  • Refactor virtual keyboard cell height for layout consistency by @Bjk8kds in #10501
  • Refactor position precision handling to honor explicit channel settings and prevent location leaks by @thebentern in #10513

🐛 Bug fixes and maintenance

⚙️ Dependencies

  • Update NeoPixel to v1.15.5 by @app/renovate in #10466
  • Update libch341-spi-userspace digest to 2e5ff75 by @app/renovate in #10485

Full Changelog: v2.7.23.b246bcd...v2.7.24.472b14c

Meshtastic Firmware 2.7.23.b246bcd Alpha

Choose a tag to compare

@github-actions github-actions released this 08 May 10:43
b246bcd

🚀 Enhancements

🐛 Bug fixes and maintenance

⚙️ Dependencies

  • Update meshtastic-esp32_https_server digest to 0c71f38 by @app/renovate in #10081
  • Update meshtastic-st7789 digest to 222554e by @app/renovate in #10121
  • Update actions/github-script action to v9 by @app/renovate in #10122
  • Update meshtastic-st7789 digest to 7228c49 by @app/renovate in #10131
  • Update pnpm/action-setup action to v6 by @app/renovate in #10132
  • Update meshtastic-st7789 digest to 4d957e7 by @app/renovate in #10134
  • Update meshtastic-st7789 digest to a787bee by @app/renovate in #10147
  • Update softprops/action-gh-release action to v3 by @app/renovate in #10150
  • Update platform-native digest to 71ed55b by @app/renovate in #10165
  • Update meshtastic-st7789 digest to 92bae2e by @app/renovate in #10182
  • Update meshtastic/device-ui digest to 5305670 by @app/renovate in #10183
  • Update meshtastic/device-ui digest to 56e1da4 by @app/renovate in #10195
  • Update GxEPD2 to v1.6.9 by @app/renovate in #10212
  • Update LovyanGFX to v1.2.20 by @app/renovate in #10232
  • Update meshtastic-esp8266-oled-ssd1306 digest to 6bfd1f1 by @app/renovate in #10277
  • Update platform-native digest to 135b91e by @app/renovate in #10300
  • Update meshtastic/device-ui digest to 7289329 by @app/renovate in #10313
  • Update platform-native digest to 4ea5e09 by @app/renovate in #10314
  • Update meshtastic/device-ui digest to 1ddcc9d by @app/renovate in #10328
  • Update meshtastic/device-ui digest to 4bf593a by @app/renovate in #10346
  • Update platform-native digest to cab4b21 by @app/renovate in #10372
  • Update LovyanGFX to v1.2.21 by @app/renovate in #10373
  • Update libpax digest to df42474 by @app/renovate in #10406

Full Changelog: v2.7.21.1370b23...v2.7.23.b246bcd

Meshtastic Firmware 2.7.22.96dd647 Alpha

Choose a tag to compare

@github-actions github-actions released this 14 Apr 12:29
96dd647

🐛 Bug fixes and maintenance

⚙️ Dependencies

  • Update meshtastic-esp32_https_server digest to 0c71f38 by @app/renovate in #10081
  • Update meshtastic-st7789 digest to 222554e by @app/renovate in #10121
  • Update actions/github-script action to v9 by @app/renovate in #10122
  • Update meshtastic-st7789 digest to 7228c49 by @app/renovate in #10131
  • Update pnpm/action-setup action to v6 by @app/renovate in #10132
  • Update meshtastic-st7789 digest to 4d957e7 by @app/renovate in #10134
  • Update meshtastic-st7789 digest to a787bee by @app/renovate in #10147
  • Update softprops/action-gh-release action to v3 by @app/renovate in #10150

Full Changelog: v2.7.21.1370b23...v2.7.22.96dd647